Materials Needed & Measurement:
- Suggested yarns: Lion Brand Vanna’s Choice or Hobby Lobby’s “I Love This Yarn!”
- Worsted Weight (Category 4) yarn – approximately 20 yards
- US I/5.50 mm hook (or hook needed to obtain gauge)
- Scissors
- Measuring Tape
- Tapestry Needle for weaving in ends
Gauge:
- Height: 2 rounds of DC = 1″
- Length: 4 DC sts = 1″
Terminology:
- CH = Chain
- DC = Double-Crochet
- St = Stitch
- Sts = Stitches
- SL-ST = Slip-Stitch
Approximate Finished Sizing:
- Diameter: 4.75″
- Yardage: Approximately 20 yards
Stitching Instructions for Mug Hug Trivet Pattern:
Round 1:
- Start by making a magic ring (adjustable ring) to begin your project.
- CH 2 (counts as the first DC), then work 11 more DC into the ring. This will give you a total of 12 DC stitches in the round.
- Once you’ve worked your 12 DC, SL-ST into the top of the CH 2 to close the round. Tighten the magic ring and pull the yarn end to close the center.
Round 2:
- CH 2 (counts as the first DC), then work 1 DC into the same stitch as the CH 2.
- Now, work 2 DC into each stitch around. To do this, place 2 DC stitches into each of the 12 DC from Round 1. You should have 24 DC stitches at the end of this round.
- SL-ST into the top of the CH 2 to close the round.
Round 3:
- CH 2 (counts as the first DC), then work 1 DC into the next stitch.
- Now, alternate between working 2 DC into the next stitch, followed by 1 DC into the next stitch. Repeat this pattern around the entire round.
- For example, you’ll work 2 DC in the first stitch, then 1 DC in the next, and repeat the pattern until you finish the round.
- You will end up with 36 DC stitches at the end of Round 3.
- SL-ST into the top of the CH 2 to join.
Round 4:
- CH 2 (counts as the first DC), then work 1 DC into the next 2 stitches.
- Work 2 DC into the next stitch, followed by 1 DC into the next 2 stitches. Repeat this pattern around the entire round.
- So, you’ll place 2 DC into one stitch, then 1 DC into each of the next two stitches, and repeat this sequence around.
- You should now have 48 DC stitches at the end of Round 4.
- SL-ST into the top of the CH 2 to join the round.
Round 5:
- CH 2 (counts as the first DC), then work 1 DC into the next 3 stitches.
- Work 2 DC into the next stitch, followed by 1 DC into the next 3 stitches. Repeat this pattern around the entire round.
- You will work 2 DC into one stitch, followed by 1 DC into each of the next three stitches, and repeat this until you finish the round.
- You should have 60 DC stitches at the end of Round 5.
- SL-ST into the top of the CH 2 to close the round.
Round 6:
- CH 1 (this chain will act as the first SC in this round).
- Work SC into each DC stitch around the entire round. You will place 1 SC in each of the 60 DC stitches from Round 5.
- Ensure you are working into the top of each DC to create a nice even edge.
- Once you’ve worked all around the trivet, SL-ST into the first SC to join the round.
Finishing:
- Cut the yarn, leaving a small tail.
- Use the tapestry needle to weave in any loose ends, making sure to weave them securely to prevent unraveling.
- Weave the yarn through a few stitches along the edge and cut off any excess yarn.
Final Dimensions:
- Diameter: Your completed Mug Hug Trivet should measure approximately 4.75″ in diameter.
- Gauge: Be sure your gauge is correct, with 2 rounds of DC equaling 1″ in height and 4 DC stitches equaling 1″ in length.
Enjoy your beautifully crocheted Mug Hug Trivet! It will make a perfect addition to your kitchen or be a thoughtful gift for someone special.
Download PDF
